Username   Password       Forgot your password?  Forgot your username? 

 

Fuzzy Reliability Analysis and Optimization Design of Hydraulic System of Bale Carrier for Tie Arm Device

Volume 15, Number 2, February 2019, pp. 416-430
DOI: 10.23940/ijpe.19.02.p7.416430

Chenghui Pei, Xingyan Liu, Zhigang Liu,Tong Zhang, and Guoliang Li

College of Mechanical Engineering, Inner Mongolia University of Technology, Huhehaote, 010051, China

(Submitted on October 15, 2018; Revised on November 13, 2018; Accepted on December 14, 2018)

Abstract:

In order to realize the vertical and horizontal arrangement of square bales, the tie arm device adopts position feedback and hydraulic two-way lock loop for position control and position locking. The corresponding simulation model is established with AMESim software to verify the correctness of the model and to study the characteristics of the hydraulic control system. The fuzzy Failure Mode Effects and Criticality Analysis (FMECA) method is applied to the hydraulic system. According to the results of the hazard degree evaluation, the order of the hazard grade of each failure mode of the hydraulic system components is obtained and can be used for the reliability improvement and maintenance of the hydraulic system. The hydraulic control system is optimized by adjusting the parameters of several important influencing factors.

 

References: 20

        1. M. S. Yang and J. M. Du, “Grassland Engineering Mechanics,” China Agricultural University Press, Beijing, 2013
        2. S. D. Yang and G. X. He, “Hydraulic Transmission and Pneumatic Transmission,” Huazhong University of Science and Technology Press, Wuhan, 2008
        3. J. Y. Zhao and Y. C. Yao, “Research Progress of Hydraulic System Reliability,” China Journal of Hydraulic Pneumatic and Sealing, No. 3, pp. 50-52, 2006
        4. C. L. Ao, X. Z. Zheng, Y. Z. Dai, et al., “Tractor Use Reliability Fuzzy Comprehensive Evaluation,” China Journal of Journal of Agricultural Mechanization, No. 4, pp. 84-87, 2004
        5. A. Z. Kellerc and K. Z. Beng, “Further Applications of Fuzzy Logic to Reliability Assessment and Safety Analysis,” Microelectronics Reliability, Vol. 29, No. 3, pp. 399-404, 1989
        6. A. C. F. Guimarães and C. M. F. Lapa, “Effects Analysis Fuzzy Inference System in Nuclear Problems using Approximate Reasoning,” Annals of Nuclear Energy, Vol. 31, No. 1, pp. 107-115, 2004
        7. J. B. Bowles and C. E. Pelaez, “Fuzzy Logic Prioritization of Failures in a System Failure Mode, Effects and Criticality Analysis,” Reliability Engineering & Systems Safety, Vol. 50, No. 2, pp. 203-213, 1995
        8. C. G. Dai, X. D. Wang, X. Zhang, and L. Wang, “Fuzzy Comprehensive Evaluation in FMECA of Electro-Hydraulic Servo Valve,” China Journal of Journal of Beijing University of Aeronautics and Astronautics, Vol. 37, No. 12, pp. 1575-1578, 2011
        9. D. Chen, C. Yao, and Z. Feng, “Reliability Prediction Method of Hydraulic System by Fuzzy Theory,” IFAC Proceedings Volumes, Vol. 46, No. 5, pp. 457-462, 2013
        10. P. Li, Z. H. Yuan, and F. Su, “Reliability Analysis of Electrohydraulic Servo Actuator based on Fuzzy FMECA,” Machine Tools & Hydraulics, Vol. 41, No. 13, pp. 178-182, 2013
        11. Q. G. Hu and X. X. Shen, “Fuzzy Reliability Analysis in FMECA of Amphibious Armored Vehicle Hydraulic System,” China Journal of Machine tools and hydraulic, Vol. 45, No. 13, pp. 16-173, 2017
        12. Y. H. Liu and J. S. Chen, “Application of AMESim Simulation Technology in Design Analysis of Hydraulic System,” Hydraulics & Pneumatics, No. 11, pp. 1-6, 2015
        13. W. T. Shi, Y. Q. Lu, Y. Lu, et al, “Design and Simulation of Hydraulic Transmission of Potato Harvester based on AMESim,” Journal of Agricultural Mechanization Research, Vol. 40, No. 8, pp. 254-257, 2018
        14. K. Zhang, X. D. Huang, Z. F. Xie, and M. Zhou, “Design and Optimization of a Novel Electrically Controlled High Pressure Fuel Injection System for Heavy Fuel Aircraft Piston Engine,” Chinese Journal of Aeronautics, 2018
        15. L. Wang, P. Zhou, M. L. Xia, et al, “Structural Optimization and Simulation of Marine Hydraulic Damper based on AMESim,” Hydraulic & Pneumatics, No. 6, pp. 94-98, 2018
        16. Z. Zhou, D. Z. Ma, X. Y. Yu, et al, “Application of Fuzzy FMECA in Analysis of Product Reliability,” China Journal of Electric Machines and Control, Vol. 14, No. 10, pp. 89-94, 2010
        17. V. R. Renjith, M. J. Kalathil, P. H. Kumar, and D. Madhavan, “Fuzzy FMECA (Failure Mode Effect and Criticality Analysis) of LNG Storage Facility,” Journal of Loss Prevention in the Process Industries, Vol. 56, pp. 537-547, 2018
        18. S. Carpitella, A. Certa, J. Izquierdo, and C. M. L. Fata, “A Combined Multi-Criteria Approach to Support FMECA Analyses: A Real-World Case,” Reliability Engineering & System Safety, pp. 169, 2018
        19. Y. Wang and B. Cheng, “Fuzzy FMECA based on Common Faults of Wind Turbine Generator,” Power System Protection & Control, 2018
        20. B. Goo, J. Lee, S. Seo, D. Chang, and H. Chung, “Design of Reliability Critical System using Axiomatic Design with FMECA,” International Journal of Naval Architecture & Ocean Engineering, 2017

         

              Please note : You will need Adobe Acrobat viewer to view the full articles.Get Free Adobe Reader

               
              This site uses encryption for transmitting your passwords. ratmilwebsolutions.com